Description
CAMTOP Safety Hammer Пневматический Быстросъёмное соединение Инструмент
2″ 1502 | 3″ 1502 | 4″ 200/206 | 4″ 602/1002 | Пневматический Operation | 90 PSI
Product Overview
The CAMTOP Safety Hammer is a pneumatic hammer union tool designed for the rapid, consistent, and safe makeup and breakout of hammer union connections used in oilfield well service applications. Engineered for high-pressure flow line connections, the Safety Hammer replaces manual sledgehammer operations, providing controlled impact force at 90 PSI air pressure to ensure proper union assembly without damaging wing nuts or union components. Available with interchangeable adapters to fit 2 inch 1502, 3 inch 1502, 4 inch 200/206, and 4 inch 602/1002 hammer union sizes.
Drive Type: Пневматический (Compressed Air) | Operating Pressure: 90 PSI | Air Requirement: 29 SCFM | Air Inlet: 3/8″ NPT | Рукав Size: 1/2″
В сборе Drawing & Parts Diagram
CAMTOP Safety Hammer Complete В сборе & Parts Diagram
Key Features
- Пневматический Operation: Powered by compressed air at 90 PSI, delivering consistent impact force for uniform union connections
- Interchangeable Adapters: Инструмент adapters available for 2 inch 1502, 3 inch 1502, 4 inch 200/206, and 4 inch 602/1002 hammer union sizes
- Ergonomic Gooseneck Handle: Curved handle design provides operator leverage and control during positioning and rotation
- Replaceable Impact Инструмент: Hardened steel impact tool is a field-replaceable consumable component for extended tool life
- Buffer System: Резиновый buffer with split upper and lower buffer washers absorbs impact shock and protects internal components
- Retainer Lock Пружина: Secures the threaded retainer in place, preventing loosening during operation
- Trigger Control: Squeeze trigger for precise impact control, allowing operator to stop immediately when connection is tight
- Filter-Lubricator-Regulator Compatible: Designed for use with air line FRL units for optimal lubrication and air quality
- Safe Alternative: Eliminates manual sledgehammer swings, reducing operator fatigue and risk of injury on the rig floor
- Consistent Torque Application: Provides repeatable makeup torque for hammer union connections when used per recommended procedures
Technical Specifications
| Parameter | Specification |
|---|---|
| Инструмент Type | Пневматический Быстросъёмное соединение Инструмент |
| Drive | Compressed Air (Пневматический) |
| Recommended Air Pressure | 90 PSI (6.2 bar) at the tool |
| Minimum Air Flow | 29 SCFM per Safety Hammer |
| Air Supply Рукав | 1/2″ minimum |
| Air Inlet Connection | 3/8″ NPT male thread plug with 1/2″ hose barb coupler |
| Available Переходник Sizes | 2″ 1502 | 3″ 1502 | 4″ 200/206 | 4″ 602/1002 |
| Control Type | Trigger-operated throttle |
| Lubrication | Air tool oil (3 cc daily before use; flush and oil weekly) |
| Recommended FRL | Ingersoll Rand C28231-800 or equivalent Filter-Lubricator-Regulator |
Parts List & В сборе
| Item | Component | Description |
|---|---|---|
| 1 | Пневматический Device | Main pneumatic impact mechanism with trigger control |
| 2 | Переходник | Selectable size adapter (2″ 1502, 3″ 1502, 4″ 200/206, or 4″ 602/1002) |
| 3 | Gooseneck Handle | Curved ergonomic handle for operator positioning and leverage |
| 4 | Impact Инструмент | Replaceable hardened steel impact anvil (consumable) |
| 5 | Threaded Retainer | Threaded housing that secures internal components |
| 6 | Retainer Кольцо | Securing ring for lower buffer washer assembly |
| 7 | Нижний Buffer Washer (Split) | Split washer for impact absorption at impact tool base |
| 8 | Резиновый Buffer (Solid) | Solid rubber cushion absorbs impact shock and vibration |
| 9 | Верхний Buffer Washer (Split) | Split washer positioned above rubber buffer for load distribution |
| 10 | Retainer Lock Пружина | Пружина-loaded lock to secure threaded retainer against loosening |
Operation Instructions
Соединение В сборе (Makeup)
- Clean and lightly oil union components. Visually inspect union seal — replace if worn, torn, or cracked
- Hand tighten the hammer union connection until the wing nut ceases to rotate
- Slide the Safety Hammer adapter over the wing nut so it bears against one of the three lugs. Orient so that the impact tool striking the wing nut lug will tighten the connection
- Apply a turning force to the gooseneck handle until the wing nut ceases to rotate
- Squeeze the trigger and apply a slight turning force to the gooseneck handle
- The connection is tight when the wing nut ceases to rotate. A noticeable change in impact sound normally accompanies this
Соединение Disassembly (Breakout)
- Slide the Safety Hammer adapter over the wing nut so it bears against one of the three lugs. Orient so that the impact tool striking the wing nut lug will loosen the connection
- Squeeze the trigger and apply a slight turning force to the gooseneck handle
- The hammer union connection is loose when the wing nut can be turned by hand
- Complete removal of the wing nut by hand
Maintenance & Lubrication
| Frequency | Action Required |
|---|---|
| Daily (Before Use) | Pour 3 cc of air tool oil into the air inlet, even when using an air line lubricator. Check retainer components are lubricated |
| Every 2-3 Hours | If no air line lubricator used: disconnect air hose, pour 3 cc oil into air inlet |
| Weekly | Flush with 3 cc cleaning solution (run 4 seconds), then lubricate with 3 cc oil (run 30 seconds) |
| Before Storage (>24 hrs idle) | Pour 3 cc oil into air inlet and operate 5 seconds to coat internal parts |
| After Maintenance | Reassemble all parts per diagram. Lubricate air inlet and operate 5 seconds |
Troubleshooting Guide
| Symptom | Likely Cause | Solution |
|---|---|---|
| Sluggish Operation | Dirt or oil gum accumulation on internal parts | Flush with 3 cc cleaning solution (4 sec), then lubricate with 3 cc oil (5 sec) |
| Loss of Power | Worn pneumatic device | Contact CAMTOP service center for pneumatic device repair/replacement |
| Low Efficiency | Worn pneumatic device and/or impact tool | Replace impact tool first. If problem persists, service pneumatic device |
| Excessive Impact Инструмент Wear | Mushrooming of impact tool contact end; excessive hammering duration | Replace impact tool. Stop hammering immediately when wing nut ceases to rotate |
Why Choose CAMTOP?
- High-quality pneumatic hammer union tools manufactured to meet demanding oilfield specifications
- Interchangeable adapters available for all common hammer union sizes
- Complete parts support: impact tools, rubber buffers, buffer washers, retainer rings, and seal kits
- ISO 9001 certified quality management system
- Competitive factory-direct pricing with global shipping and logistics support
- Technical guidance on proper hammer union makeup and breakout procedures
Contact CAMTOP
Email: sales@cposl.com
Phone: 86-18621723891
Website: www.camtop-oilfieldtools.com
Address: No. 432, Fute North Road, Pudong District, Shanghai, China
